LED dimmer RF WiFi wireless, 2 channel surface mounted pushbutton dimmer with glass frame

RF WiFi series wireless 2nd channel surface mount pushbutton dimmer with glass frame, i.e. two buttons. Very easy to install and use! Compatible with all our RF WiFi series products.

Surface-mounted 2nd channel LED-dimmer with two buttons

Requires 12-24V to operate LED-for controlling tapes e.g. RF WiFi dimmer/receiver  or 230V control (i.e. for TRIAC dimmable luminaires or TRIAC transformers) 230V TRIAC wireless RF dimmer.

You need a receiver for each button/button, so you can use this to implement kitchen lighting, for example:

1. the button controls the receiver connected to the transformer of the kitchen worktop light profiles and

2. the button controls the LED strips for indirect lighting installed on the upper kitchen cabinets via their own receiver, which also has its own receiver. power supply attached to the receiver itself.

The push-button act as a normal on/off switch on its own buttons and, with a long press, dims and brightens the light. The colour is white. For wall or furniture mounting, can also be mounted directly on stall boxes used in Finland. Easy to retrofit, as there is no wiring at all for the roller control, which works with a battery. In addition to the wall controller, the dimming of the strip can be controlled from a smartphone if an RF WiFi converter is installed in the same system.

Several receivers (8) can be paired to the controller.

- Operating distance approx. 20m

- IP20

- Powered by 3V battery (CR2430), battery life approx. 2-3v, battery included. The battery can be replaced.

- operating frequency 868MHz

- can be paired with multiple receivers

- white plastic

- size 86 x 86mm, height 13,8mm

Compatible RF WiFi series receivers for this wireless controller:

Monochrome dimmable LED-strips

• 12-24V for dimmable monochrome LED-tapes (max. 96W 12V LED-ribbon or 192W 24V LED-tape) : LED-receiver 1 x 8A LED-receiver 12-36V - RF WiFi
• If you install more LED-tapes, up to 5 x 120W 24V LED-tapes: 4 x 5A for monochrome LED-RF WiFi for ribbons (NOTE! (all ribbons installed in this receiver will work at the same time as one group)
• If you install more LED-ribbons, up to 5 x 1192W 24V LED-tapes: 4 x 8A for monochrome LED-RF WiFi for ribbons (NOTE! (all ribbons installed in this receiver will work at the same time as one group)

 

230V LED-lamps with transformers and LED-lamps and bulbs such as E27, E14, etc.

• 230V TRIAC for dimmable LED-lamps and dimmable lamps LED-for incinerators: 230V TRIAC dimmer - RF WiFi
• 230V ON/OFF RELE for all types LED-luminaires: 230V ON/OF RELE - RF WiFi

 

Connecting the receiver to work with a remote control or button controller:

• Connect to LED strip to the receiver
• Turn on the button/remote control by removing the protection between the radiator and the button/regulator, then the button/regulator starts working
• Activate the button/remote control with the ON button and press the receiver's Learning key-button on the receiver briefly. Immediately afterwards, press the button on the controller to which you want to connect the lights
• The connection is complete when LEDthe :s flash

One receiver can be controlled by more than one button (max. 8 buttons), if you want to control the light from both doorways of a room.

Disconnection of receiver and button/remote control:

• Press the learning key button for 5 seconds.

Requires 12-24V to operate. LED-tapes e.g. RF WiFi dimmer/receiver  or 230V control (i.e. for TRIAC dimmable luminaires or TRIAC transformers) 230V TRIAC wireless RF dimmer.

The product's own plastic frame is removable and can be replaced with a frame from Schneider's Exxact series: e.g. Primo, Combi, Design or Solid.

3 years warranty.